2HP 110-240V Hayward Inground Swimming Pool pump motor Strainer Replacement

  

2HP 110-240V Hayward Inground Swimming Pool pump motor Strainer Replacement. Always pay attention before use. Before use, please adjust to the corresponding voltage for home use, and then fill the water pump with water before using it, otherwise the motor will be damaged. When adjusting the voltage, be sure to adjust after turning off the power. Otherwise the motor will be damaged.

This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean.

Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools.

Durable Corrosion -Stainless Steel 2.0 HP Shaft, the shaft is constructed with a reinforced thermoplastic body for longer life and durability. The sand filter is made of PPGF30 + PC, 100% drip proof, effective insulation and protection against. Pool chemicals, heat-resistant double-sized seal for long motor life. POOL PUMP-This self-priming heavy-duty pump delivers outstanding performance and reliability at a fantastic price and costs less than big name brands. The mighty force of this pump makes it efficient and an economical choice.

UL Certified- This Swimming Pool Pump has a UL Certification to ensure recognized Standards for Safety. Motor Shaft Material: Stainless Steel. Pump Housing Material: PPGF30 + PC (anti-Oxident).

Inner/Outer coupling: 1-1/2''NPT G2-1/4'. 2 x 1-1 / 2''NPT Inner coupling. 2 x 48.5mm Inner coupling(free gift). Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification.

If you wire it yourself, the machine will not work properly. Thank you for your cooperation. The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out. The pump head is not filled with water, causing the pump to run without water. During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head. During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water. When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes. Before pumping, the pump head should be filled with water. Inlet and outlet joints wrapped around the raw material tape, beware of leaks.

Tightening when installing the inlet and outlet, beware of leaks. The pump head transparent cover is tightened to prevent air leakage and water seepage.

The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn. The pump prevents the inlet from entering the water and burns the motor.

There is Water in The Pump. Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal.

The Pump stop working suddenly. Our company's products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process , generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise , pump stop working.

Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller. Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused. The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter.

Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Used items will not be accepted for return. We will reply you ASAP. Our aim is to provide Top Level Customer Service, so we will try our best to solve any problem.

The item "2HP 110-240V Hayward Inground Swimming Pool pump motor Strainer Replacement" is in sale since Tuesday, August 24, 2021. This item is in the category "Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps". The seller is "yunli1993" and is located in Chino, California. This item can be shipped to United States.

• Brand: Unbranded
• Type: Swimming Pool Water Pump
• Voltage: 110-120V/220-240V 60Hz
• Model: 2040700200M
• MPN: 2040700200M
• Custom Bundle: No
• Modified Item: No
• Style: Modern
• Speed: Max Flowrate: 410L/min
• Horsepower: 2hp
• Pool Type: Above-Ground
• Color: Black
• Rated Power: 1500W/2.0HP
• Max Flow Rate: 410L/min
• UL Approval: Yes
• Inner/Outer coupling: 1-1/2''NPT G2-1/4''
• Pump Housing Material: PPGF30 + PC (anti-Oxident)
• Motor Shaft Material: Stainless Steel
• Max Height: 12.5M