2.5HP 110V Swimming Pool Pump In/Above Ground with Motor Strainer Filter Basket

  
American Business ALL ITEMS IN STOCK IN CALIFORNIA. American STANDARD PRODUCTS QUALITY GUARANTEED. 2.5HP Swimming Pool Pump Self-Priming Spa Above In Ground 1850w Motor. Item was as described and arrived quickly. Maintain a crystal clear and sparkling pool or spa that everybody loves with the new SPPE series self-priming 1850W electric swimming pool pump. The pump is copper winding motor, Inner diameter of pump tube: 48.5mm (2''), Outer diameter: 54.5mm (2.1''), suitable for 1 1/2'' PVC pipe, max flow rate: 51 GPM, and it has a convenient drain plug and comes with standard three-prong plug connection. NOTE: This pump has NO INTERNAL THREAD!!!

High Efficiency & Low Noise? High efficiency impeller and superior internal flow design maximize flow rate 51GPM/min Hand reduce hydraulic noise.

The result is an ability to move more water for lower operating cost and less wear and tear. This heavy-duty pump delivers outstanding performance and reliability through powerful motor and airflow ventilation for smoother run-time experience. The 2.5HP, 51GPM strong pump makes it an efficient and an economical choice. This pump includes a large basket to collect hair, lint and leaves to ensure free-flowing operations at all times, while the clear cover lets you see exactly when the basket needs cleaning.

And exclusive cover shape makes for easy strainer removal without tools. Reinforced Pump Body & Housing? 2.5HP pool pump body is made of reinforced PP material. And the motor of the pool pump is a pure copper motor.

The motor shell is made of an aluminum stretched casing. This design can make the pump more heat dissipation and impact resistance. The swimming pool pump must be filled with water before it can be turned on and run. Otherwise, it will cause dry grinding of the mechanical seal and cause heat generation to damage the impeller, and finally cause the water pump to leak(water). Learn about a common mistake you can make when installing your pool pump.

Using a fitting that causes a flow restriction really close to the pump's suction intake could cause premature damage or failure. Advise 5x pipe diameter of straight pipe run into the pump as a minimum. So 2" pipe requires at least 10" of straight pipe run into the suction side of your pool pump as the minimum installation standard. Locate the pump as close as possible to the pool.

The pump suction line should not be smaller than the pressure line. All piping must be airtight 3. The threads on the pump must be sealed with Teflon Tape or Silicon, when the pump unions are screwed on. The weight of the piping should be supported independently and not carried by the pump.

Fill the pump tank with water before starting. High suction lifts, or long suction lines, require additional time and reduce the performance of the pump. The water being pumped cools and lubricates the seal. After the pump tank has been filled with water, and the motot started, allow a few moments for the pump to start delivering water. The installation must be according to the normal power indicated on the label. The amperage must not at any time exceed the value indicated on the label It is recommended that you consult a state-registered electrician. Place the pump in a dry area with good ventilation. The ambient temperature must not exceed 40?

The pumps are only suitable for counter-clockwise rotation when viewing from the pump end. Three phase motors can rotate in either direction.

Interchanging any of the cables on a three-phase motor will reverse the rotation. Momentarily start, or bump the motor without water in the tank, to check the rotation of the pump shaft. Before disconnecting electrical connections, shut off electricity at its source. Newer work on pump without making certain the power is OFF.

This appliance is not intended for use by persons, including children with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible for their safety Children should be supervised to ensure that they do not play with the appliance. NOTE: 2.5HP swimming pool pump also include 2 adapter. Powerful Self-Priming IP55 2.5HP Electric Motor, low noise with quiet operation and no leak.

Suitable for pools up to 100,000 litres. Advanced S-Tek Flow System For Increased Efficiency With Continuous Flow Rate Of 560L/min. Full Size Removable Strainer Basket.

100% Salt and Chlorine compatible. Full Commercial Duty - Designed to run 24/7. Works with In ground and Above Ground.

Ideal for Residential/Commercial Swimming Pools & Spa's. Head : Max 19m / 62.34ft. Pipe Compatibility : Fit 1.5 plumbing internally and 2 inch. Weight : 10.2 kg / 22.5 lbs.

SPPE250 Swimming Pool Pump x 1. User's Manual x 1.

All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers - Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification.